BADU®Mat R 51, R 40 & R 40 T

6 Way Multiport valve with clear rinsing feature

Sand filters must be backwashed in order to loosen up the sand and to eliminate filtered dirt through the waste system. This requires, among other things, that the hydraulic action of the filter circulation pump be reversed through the filter housing.

These function as well as others can be adjusted easily and effortlessly with the BADU®Mat. The BADU®Mat is fully factory tested and together with the internal parts carries a 24 month ex-factory warranty from date of purchase.

MULTIPORT VALVE OPERATION

FILTER: In this position the pool water is pumped into the filter where sediment and dirt are trapped in the sand bed, allowing only clean water to return to the pool.

BACKWASH: In this position the pool water is pumped into the filter, dirt and collectable particles in the sand bed are dislodged and washed down the waste line. Backwash the pool for approximately 3-5 minutes or until the water, visible in the sight glass on the side of the Multiport valve becomes clear.

RINSE: In this position the pool water is pumped through the filter down the waste pipe. This position is used immediately after backwashing to rinse and settle the sand before switching on the filter approximately 3 minutes after every backwash. After backwashing, fresh water must be fed into the system in order to re-establish the original water level.

RECIRCULATE: In this position water from the pump will bypass the filter sand bed.

WASTE: In this position the pool water is pumped through the multiport valve direct to the waste line, bypassing the sand bed. This position can be used when the pool has a large buildup of dirt and leaves and alleviates the necessity for backwashing after vacuuming. Waste position should only be used for short periods as large volumes of water will be pumped down the waste line which may result in the pool water level falling below the skimmer level.

CLOSED: In this position the multiport valve is closed off and water from the pump will not pass through the filter. This position should only be used when cleaning the primary strainer.

NOTE: Do not operate the pump with the valve in the closed position or when turning to a position on the valve.

LID MPV COMPLETE WITH O-RING
BADU®ECO WISE 1
BADU MAT R40/3 GK-SA INC PIPE
BADU®ECO WISE 1
LID JUMBO COMPLETE WITH O-RING
BADU®ECO WISE 1
BADU MAT R51 INCLUDING PIPE
BADU®ECO WISE 1
gemini twinsweep specs-crop-u73017

BADU®Mat Spares

ADAPTOR SOCKET 75x63x2” MALEX
CARTRIDGE-ELEMENT-ECO-1
PVC PIPE 63mm
CARTRIDGE-ELEMENT-ECO-1
PVC ELBOW 50mm 90 LP
CARTRIDGE-ELEMENT-ECO-1
PVC ELBOW 63 mm 90 HP
CARTRIDGE-ELEMENT-ECO-1
PVC ADAPTOR 50 OD X 1 1/2″ THR
CARTRIDGE-ELEMENT-ECO-1
PVC SOCKET 63 mm
CARTRIDGE-ELEMENT-ECO-1
ADAPTOR 50 X 63 X 2″
CARTRIDGE-ELEMENT-ECO-1
B44 LOCKING NUT SAWTOOTH
CARTRIDGE-ELEMENT-ECO-1
UNION END 50mm NEW
CARTRIDGE-ELEMENT-ECO-1
LOCKIN NUT II/65mm
CARTRIDGE-ELEMENT-ECO-1
UNION BUSH II/R 2″
CARTRIDGE-ELEMENT-ECO-1
UNION END II/63mm ID GLUE
CARTRIDGE-ELEMENT-ECO-1
TEFLON DISC WASHER
CARTRIDGE-ELEMENT-ECO-1
PROFILE GASKET MPV R40
CARTRIDGE-ELEMENT-ECO-1
O-RING 25X4mm SITE GLASS
CARTRIDGE-ELEMENT-ECO-1
FILTER SITE GLASS
CARTRIDGE-ELEMENT-ECO-1
O-RING 134X4 BADU MAT
CARTRIDGE-ELEMENT-ECO-1
LID M-PORT
CARTRIDGE-ELEMENT-ECO-1
HANDLE MULTI-PORT VALVE
CARTRIDGE-ELEMENT-ECO-1
O-RING 49.2X 3.5
CARTRIDGE-ELEMENT-ECO-1
LOCKING NUT II/65mm
CARTRIDGE-ELEMENT-ECO-1
UNION END II 63mm
CARTRIDGE-ELEMENT-ECO-1
O-RING 160 X 4.5 – R-50 LID
CARTRIDGE-ELEMENT-ECO-1
WASHER MPV 29x52x2mm
CARTRIDGE-ELEMENT-ECO-1
O-RING IMPELLER CAP 11*2.5
CARTRIDGE-ELEMENT-ECO-1
O-RING 50 x 3
CARTRIDGE-ELEMENT-ECO-1
O RING 55×3.5mm JUMBO MPV
CARTRIDGE-ELEMENT-ECO-1
O-RING 58 X 5 ST TANK
CARTRIDGE-ELEMENT-ECO-1
1/4” PLUG FOR M-PORT VALVE
CARTRIDGE-ELEMENT-ECO-1
NUT FOR MULTIPORT S/ST. M6
CARTRIDGE-ELEMENT-ECO-2
PHILIPS HEAD SCREW M6X35 S/ST
CARTRIDGE-ELEMENT-ECO-2

Do you have any questions concerning this product?







Select Your Province


Product interested in: